Hand-held flue gas analyzer Model: 12 MD10GA-library number: M281542 
 The handheld gas analyzer MD10GA,-12 for more information >>> 
 Configuration: 
 1.CO range 0-2000ppm 
 2.O2 range :0-30% 
 Calculation of CO2, all relevant combustion parameters 
 4.150mm flue gas probe 


 Hand-held flue gas analyzer, compact, low cost, the use of electrochemical sensors 

 Minimum combustion gas analyzer. Although the compact but perfectly formed analyzer. Can be equipped with three electrochemical sensors. Is relative to the larger analyzer an economical compact choice. Particularly suitable for rapid short-term measurements in a small boiler system. Structure in line with the EN50379 standard. 

 Standard configuration 

 Gas composition measurements 
 Electrochemical sensing unit, two groups of standard equipment: O2, CO, 
 Can be another matching a set of sensor NO 
 Ambient CO measurement resolution of 0.1ppm 
 Other parameters measurement 
 Gas and ambient temperature measurements 
 Pressure, partial pressure measurement with a resolution of 0.1 Pa, 
 Flow rate measurement 
 Relative humidity measuring probe - optional 
 Calculate 
 CO2 concentration 
 All relevant combustion parameters 
 Display and processing of measurement data 
 Screen to display all results 
 The average of all measured values. Average hours: 2, 10, 20, 30, 60, 120, 180 seconds 
 All measured values ??to the chart shows 
 The report of the 16 sets of measurements of the store - "measurement, print out later" 
 The power of the PC program the instrument settings and data transmission 
 Software features 
 Boot automatically after the initial zero point correction 
 All the settings from the PC program 
 Standard built-in six kinds of fuels (from DIN or OENORM) 
 Four kinds of users can edit the fuel data 
 Automatic detection of the device can produce audible warning and the exact message displayed on the control - the list screen 
 Hardware performance 
 Built-in clock / calendar 
 Infrared port to connect an external printer 
 A set of batteries available for operating expertise 75 hours 
 Large size 66 * 36mm] LCD LCD 
 Gas probe with thermocouple and condensate trap 
 RS-232C interface for communication with a PC 
 FLASH ROM 
 Easy, similar to the use of mobile phones as simple as 

 Options 

 Instrument of leather boxes and rubber protective sleeve 
 Backlight 
 Magnet board, for the adsorption apparatus on the plate 
 External printer for wireless infrared transmission 

 Technical parameters 

 Dimensions: W x D x H 245 x 116 x 45mm 
 Weight 600 g 
 Probe length 150 mm 
 Tracheal length of 2 m 
 20 μm filter 
 Display panel 38 x 6 6mm 
 Power 6 V (4 x AA) battery 
 External power supply 9 VDC, 
 Diaphragm 
 Operating temperature 10 ° C ÷ 50 ° C 
 Storage temperature -20 ° C ÷ +55 ° C 

 Parametric methods range resolution accuracy minimum detectable value of the response time (T90) 
 CO2 - carbon dioxide, the volume concentration calculated based on the concentration of O2 volume to 0 .. 25% 0.01% ± 0.2% or 
 2% of the rel. 0.01% 45 seconds 
 CO - Environmental concentration of carbon monoxide electrochemical sensor 0 .. 100 ppm 0.1 ppm ± 0.5 ppm or 
 5% the rel. 0.1 ppm, 45 seconds 
 O2 - oxygen, the volume concentration of the electrochemical sensor 0 .. 25% 0.01% 0.20% 0.20% 45 seconds 
 CO - carbon monoxide, the concentration of the electrochemical sensor 0 .. 20 000 ppm, 0.1 ppm, or 
 1 ppm, ± 5 ppm or 
 5% rel. 1 ppm, 45 seconds 
 COmg - carbon monoxide, mass concentration calculated by the CO volume concentration 0 .. 1 mg/Nm3 ± 5 mg/Nm3 
 or 5% the rel. 1 mg/Nm3 45 seconds 
 COrel - carbon monoxide relative O2 concentration calculated by the volume concentration of CO and O2 obtained ± 5, 0 .. 1 mg/Nm3 mg/Nm3 
 or 5% the rel. 1 mg/Nm3 45 seconds 
 NO / NOx concentration of nitrogen oxide electrochemical sensor 0 .. 1000 ppm, 0.1 or 1 ppm ± 5 ppm, or 5% rel. 1 ppm, 45 seconds 
 NOmg / NOxmg mass concentration of nitrogen oxides calculated from volumetric concentration of NO 0 .. 3 mg/Nm3 ± 3 mg/Nm3 
 or 5% of the rel. 3 mg/Nm3 45 seconds 
 The NOrel / NOxrel nitrogen oxides relative O2 concentration calculated from volumetric concentration of NO and O2 0 ... 3 mg/Nm3 ± 3 mg/Nm3 
 or 5% of the rel. 3 mg/Nm3 45 seconds 
 Tgas - flue gas temperature thermocouple -10 .. 1000 ° C, 0.1 or 1 ° C ± 2 ° C, or 1.5% rel. 1 ° C for 30 seconds 
 Unless otherwise specified. Tamb - atmospheric temperature thermal resistance -10 .. 100 ° C, 0.1 or 1 ° C ± 1 ° C, 1 ° C for 30 seconds 
 Ti-(CO/CO2- index) calculated value of 0 ... 0.01 0.0001 0.0001 
 Lambda - the amount of excess air to calculate value of 1 .. 10 0.01 0.01 
 qA - combustion losses calculated value of 0 .. 100% 0.1% 0.1% 
 Eta - the efficiency of the calculated value of 0 .. 120% 0.1% 0.1% 
 Pressure on the DMS bridge, -25 hPa ... 
 +25 HPa 0.1 or 1 Pa, ± 2 Pa or 
 5% the rel 0.1 Pa, 10 seconds 
 Static pressure the DMS bridge -25 hPa ... at +25 hPa 0.1 or 1 Pa, ± 2 Pa, or 5% rel. 0.1 Pa, 10 seconds 
 V-flow pitot tube 1 .. 30 m / s, of 0.1 m / s, of 0.5 m / s or 
 The rel. 2% of 1 m / s, 10 seconds 
 Rh-capacitive relative humidity sensor 5 .. 95% 0.01% 2% rH is or 
 The rel 2% 5% 10 seconds 



 Historical information on :2007-09-17 version of the handheld flue gas analysis the instrument MD10GA-12